Blue point Microscan III Instrukcja Użytkownika Strona 18
- Strona / 72
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
11
On-Board Diagnostics (OBD) Basics Diagnostic Services Introduction
4.3 Diagnostic Services Introduction
The OBD program is divided into several sub programs, called Services:
• Service $01: on page 13 is used to display current data
• Service $02: on page 13 is used to access powertrain freeze frame data
• Service $03: on page 14 is used to display emission related DTCs
• Service $04: on page 16 is used to clear or reset emission-related diagnostic data
• Service $05: on page 17 is used to display oxygen sensor monitoring test results
• Service $06: on page 20 is used to display specific monitored systems test results
• Service $07: on page 22 is used to display emission related DTCs detected during current or
last completed drive cycle
• Service $08: on page 23 is used to access on-board activation tests
• Service $09: on page 23 is used to access vehicle information and performance tracking
• Service $0A: on page 24 is used to display emission related DTCs with permanent status
4.3.1 Readiness Monitor Test Status
OBD-II/EOBD stipulates the monitoring (continuous or non-continuous) of the functions of the
following emission control related subsystems):
NOTE:
i Not all data is applicable or supported by all vehicles.
Each vehicle manufacturer has unique monitor test criteria. The Readiness Test Status indicates
whether a particular diagnostic monitor or function passed its specific test criteria and was found
to be within specification.
Monitors should run and set the Readiness Test Status during normal vehicle operation. The
OBD-II Drive Cycle (Figure 4-1) can be used to drive the vehicle in a prescribed manner.
Table 4-1
Continuous or Non-continuous monitors
Readiness Monitor Remark
Misfire monitoring Continuous
Fuel system monitoring Continuous
Comprehensive component monitoring Continuous
Catalyst monitoring †
Heated catalyst monitoring †
Evaporative system monitoring †
Secondary air system monitoring †
A/C system refrigerant monitoring †
Oxygen sensor monitoring †
Oxygen sensor heater monitoring †
EGR system monitoring †
† Will only be monitored if the correct conditions are met.
- User Manual 1
- Trademarks 3
- Copyright Information 3
- Visit our websites at: 3
- For Technical Assistance Call 3
- Safety Information 4
- Important Safety Instructions 5
- Contents 6
- Using This Manual 8
- 1.1.5 Hyperlinks 9
- 1.1.6 Procedures 9
- Introduction 10
- • SAE J1850 (VPW and PWM) 11
- • SAE J1939 HD OBD (optional) 11
- • ISO 9141-2 11
- • ISO 14230-2 (KWP 2000) 11
- • ISO 15765-4 (CAN) 11
- 2.3 Connections 12
- 2.4 Power Supply 12
- 2.5 Data Cable 13
- Getting Started 14
- 3.3 Powering On the Unit 15
- 3.4 Selecting a Language 16
- On-Board Diagnostics 17
- (OBD) Basics 17
- 4.3.2 MIL Status 19
- 4.4.1 Service $01: 20
- 4.4.2 Service $02: 20
- 4.4.3 Service $03: 21
- Position 1 22
- Position 2 22
- Position 3 22
- Position 4 & 5 22
- 4.4.4 Service $04: 23
- Oxygen Sensor Output 24
- O2 Monitor Test ID Table 25
- 561A 2A 3A 4A 26
- 1B 2B 3B 4B 26
- 4.4.6 Service $06: 27
- • Test Value (Results) 28
- • Minimum Test Limit 28
- • Maximum Test Limit 28
- Non CAN Protocol 28
- 4.4.7 Service $07: 29
- 4.4.8 Service $08: 30
- 4.4.9 Service $09: 30
- 4.4.10 Service $0A: 31
- Navigation 32
- 5.1.2 Main Body 33
- Menu Screens 34
- Data Screens 34
- 5.1.3 Toolbar 35
- 5.2 Screen Messages 36
- 5.2.2 Confirmation Messages 37
- 5.2.3 Warning Messages 37
- 5.2.4 Error Messages 37
- Operations 38
- Readiness Monitors 39
- Current Data 39
- Operations Main Menu 40
- List View 41
- Graph View 41
- Freeze Frame Data 43
- Clear Codes 44
- O2 Monitors 45
- 6.1.2 OBD-I 46
- 6.1.3 Make Specific Enhanced 46
- 6.1.4 Antilock Brake Systems 46
- 6.1.5 Global OBD-2/EOBD Help 46
- 6.1.6 Select Protocol 47
- 6.1.7 Captured Movies 48
- 6.1.8 Tools 49
- Language 50
- Units of Measurement 50
- Information 51
- Tool Help 51
- File Manager 51
- Touch Screen Calibration 52
- (1/4 step) 52
- Please Click the Point 52
- 6.2 USB Power Menu 53
- Data Parameters 54
- 7.1.1 Short Parameter Names 58
- 7.1.2 DTC Association 61
- Maintenance 65
- Software License Agreement 66
- Product Warranty 71
Powiązane produkty i podręczniki dla Elektronika samochodowa Blue point Microscan III
(0 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji